Electric Tankless Water Heater Installation Requirement

Without using any storage tank, an electric tankless water heater can heat the water. If you turn on your hot water outlet, cold water goes to the water heater’s unit.

Then the resistance coil helps to heat the water, which is coming through the pipes. By setting up the exact tankless water heater, you can get enough hot water comfortably.

A tankless water heater helps to save your energy supply. Nowadays, Electric water heaters can fulfill your demand for both the home and the industry. It comes with many variations in structure and features. But all structures of the unit are always the same.

So, you will need electric tankless water heater installation requirements when you buy any electric water heater.

Electric Tankless Water Heater Installation Requirements Tools

Some tools are required to set up. Such as:

Installation Requirements Tools

  • Drill
  • Flathead screwdriver
  • Phillips head screwdriver
  • Needle nose pliers
  • wrench
  • Pipe cutter
  • Pencil

Requirements Are Needed To Install The Heater 

If you want to install your electric water heater, you will need to know some electric tankless water heater requirements. The requirements have given below:

Suitable Electric Connection 

Every home is not perfect for setting the electric tankless water heater. Because the system is quite costly and challenging.

An Example Is Given Below:

Nowadays, Stiebel Eltron Tempra 36 plus is the top-rated product of electric tankless water heaters. It needs three separate dedicated 50 A, which are mainly double pole breakers.

Usually, these heaters use electricity with the leading service of 300 A at least.

So, upgrading your old electrical service such as bigger wires, more significant breakers, or setting completely new electricity is necessary for the electric tankless water heater.

The Necessity Of Water Pressure

For working properly, the electric tankless water heater needs water pressure, which range is between 30 to 150 PSI. Sometimes incoming water pressure is above 150 PSI; then, you must be installed a reducing pressure valve.

Checking For Safety

If you have a water heater, you will permit checking the water heater. It can also be a replacement for the old water heater.

When you allow, the plumbing inspector comes to your home to check it and ensure that your water heater works properly.

Select A Place

While setting your tankless water heater, you need to select a location where most hot water uses. For this reason, you can get warm water as soon as possible after opening the outlet.

It would be best if you chose a perfect place close to the most point usage because the water can reach easily to the outlet. Sometimes tankless water heaters should install with the power and water supply connection, situated on the downward.

Installment Steps Are Given Below:

  • Firstly, you need to turn off the power supply which is involved.
  • Then, the main water supply has to be closed.
  • Draining your old water heater.
  • If you want to install it, you will remove screws that help protect the unit’s front cover. When you take off the front cover, you have to be very careful.
  • Set up the hot and cold water connection.
  • Must be installed a shut-off valve that helps turn off the water supply without shutting off the whole power supply for home safety.
  • You also need to set a reduced water pressure valve that keeps your tankless water heater safe from damage.
  • Open all the water tubes for refining the pipes and water heater.
  • Check all the connections properly so that leakage can be found or not.
  • Turn off the outlet.
  • Heaters connect to the electric connection, and the other side connects to the electric panel.50A double pole breaker can be useful for the single circuit connected to the small unit. Two or even three separate courses also are beneficial for larger teams.
  • Then check all the electrical connections double.
  • It would help if you were on the circuit breakers.
  • Finally, you can turn on your electric tankless water heater.
  • If you want to check your water heater, open the water outlet until hot water comes. Then you can check the hot water temperature and change it as your wish.


  • Are the tankless water heaters smell?

Sometimes, hot water bacteria react to aluminum or magnesium’s anode, attracting corrosive water elements. For this reaction, the tankless water heaters can produce odors in the water like rotten eggs smell.

  • How often the tankless water heaters need to be cleaned?

If you want to maintain your heater correctly, you will clean your tankless water heater. The essential part is flushing at least one year, which areas mineral deposits. You have to clean your heater for tankless water heater performance well.

Is vinegar useful to clean my electric water heater?

Yes. Vinegar is helpful to clean your tankless water heater. It needs to be performed flush with food-grade. You can use white vinegar at least once every 12 to 18 months. I hope doing this will improve the efficiency of your water heater.


It is not hard to install an electric tankless water heater. Tankless water heater installation is more manageable than other water heaters. It can also heat your water what you need.

If you set up all-electric tankless water heater installation requirements correctly, your water heater will get long life and work smoothly for many years.  

About The Author

Leave a Comment